PI serial adaptor

p_20180527_114052-600

Raspberry pi serial adaptor from Facelesstech:

If you spend a lot of time building things with a raspberry pi you will eventually run into the problem that you have booted your pi it’s not plugged into a tv/monitor and it’s not connected to wifi. You don’t want to just turn it off because it could corrupt the sd card so what do you do. I recently ran into this problem but luckily I had a serial adaptor on hand to hook up and tell my pi to turn off.

See the full post on his blog and the GitHub repository here.

Check out the video after the break.

from Dangerous Prototypes https://ift.tt/2kGZjMS

ETA Nixie tube clock

ETA Nixie Tube Clock-600

Mark Smith over at surfncircuits has a nice write-up about building an ETA Nixie Tube Clock:

This DIY project will combine the estimated time of arrival function with a Nixie tube display to create an estimated time of arrival (ETA) Nixie tube clock. It is all easily controlled by a Raspberry Pi Zero W that is connected to the internet through WiFi to provide the latest time and gets the ETA for any number of destinations. The travel time is provided by the free Google Directions API interface that includes traffic to give the best estimates on any particular day.   The goal is that with an ETA Nixie tube clock, no math is needed to add a rough, often optimistic travel time, to the actual time to determine if we are running late.   The clock does that for you and with the power of IOT, is much more accurate!    A motion sensor is also added to the clock to turn off the Nixie Tube Display when no one is around, saving power and increasing the Nixie tube lifetime.

Build log at www.surfncircuits.com. Project files are located at Github.

from Dangerous Prototypes https://ift.tt/2IXAif5

CANable: the open source USB to CAN adapter

canable

An open-source USB to CAN adapter:

It supports CAN bit-rates of up to 1 Mbit/s. The product comes with an open-source SocketCAN driver software. It features a Micro-USB connector and a 4-pin screw terminal with CAN_H, CAN_L, 5-V supply, and ground. The CANable device is a hardware clone of Eric Evenchick’s CANtact project, an open-source USB-to-CAN hardware adapter

Via Open Electronics.

from Dangerous Prototypes https://ift.tt/2LIJaCL

Arduino time attendance system with RFID

circuit-600

A how-to on building a time attendance system with MFRC522 RFID Reader and Arduino from Random Nerd Tutorials:

Before getting started it’s important to layout the project main features:
*It contains an RFID reader that reads RFID tags;
*Our setup has a real time clock module to keep track of time;
*When the RFID reader reads an RFID tag, it saves the current time and the UID of the tag in an SD card;
*The Arduino communicates with the SD card using an SD card module;
*You can set a check in time to compare if you are in time or late;
*If you are on time, a green LED lights up, if you are late, a red LED lights up;
*The system also has a buzzer that beeps when a tag is read.

More details at randomnerdtutorials.com.

Check out the video after the break.

from Dangerous Prototypes https://ift.tt/2IVH4h8

#FreePCB via Twitter to 2 random RTs

IRToy-600x369

Every Tuesday we give away two coupons for the free PCB drawer via Twitter. This post was announced on Twitter, and in 24 hours we’ll send coupon codes to two random retweeters. Don’t forget there’s free PCBs three times a every week:

  • Hate Twitter and Facebook? Free PCB Sunday is the classic PCB giveaway. Catch it every Sunday, right here on the blog
  • Tweet-a-PCB Tuesday. Follow us and get boards in 144 characters or less
  • Facebook PCB Friday. Free PCBs will be your friend for the weekend

Some stuff:

  • Yes, we’ll mail it anywhere in the world!
  • Check out how we mail PCBs worldwide video.
  • We’ll contact you via Twitter with a coupon code for the PCB drawer.
  • Limit one PCB per address per month please.
  • Like everything else on this site, PCBs are offered without warranty.

We try to stagger free PCB posts so every time zone has a chance to participate, but the best way to see it first is to subscribe to the RSS feed, follow us on Twitter, or like us on Facebook.

from Dangerous Prototypes https://ift.tt/2L3okwO

Microsoft “Intellimouse” teardown

ms_mouse_total-600

Microsoft “Intellimouse” teardown from Electronupdate:

Before the advent of optical mice, the go to technology was a steel ball which moved two drive shafts to indicate position.
A good example of this is this Microsoft “Intellimouse”.
As expected the electronics are built around a small micro controller

Check out the video after the break.

from Dangerous Prototypes https://ift.tt/2xmrMR7

Raspberry Pi GPIO programming in C

Raspberry-GPIO

Steve Chamberlin has written an article about Raspberry Pi GPIO programming in C:

The Raspberry Pi’s 40-pin GPIO connector often gets overlooked. Typical Pi projects use the hardware as a very small desktop PC (RetroPie, Pi-hole, media center, print server, etc), and don’t make any use of general-purpose IO pins. That’s too bad, because with a little bit of work, the Raspberry Pi can make a powerful physical computing device for many applications.

More details at Big Mess o’ Wires homepage.

from Dangerous Prototypes https://ift.tt/2se4Pe4

Free PCB Sunday: Pick your PCB

BP-600x373

We go through a lot of prototype PCBs, and end up with lots of extras that we’ll never use. Every Sunday we give away a few PCBs from one of our past or future projects, or a related prototype. Our PCBs are made through Seeed Studio’s Fusion board service. This week two random commenters will get a coupon code for the free PCB drawer tomorrow morning. Pick your own PCB. You get unlimited free PCBs now – finish one and we’ll send you another! Don’t forget there’s free PCBs three times every week:

Some stuff:

  • Yes, we’ll mail it anywhere in the world!
  • Be sure to use a real e-mail in the address field so we can contact you with the coupon.
  • Limit one PCB per address per month please.
  • Like everything else on this site, PCBs are offered without warranty.
  • PCBs are scrap and have no value, due to limited supply it is not possible to replace a board lost in the post

Be the first to comment, subscribe to the RSS feed.

from Dangerous Prototypes https://ift.tt/2IRZvYl

App note: How to properly configure unused operational amplifiers

an_ti_sboa204

Good read app note from Texas Instruments about configuring unused op amps on multi amp chips. Link here (PDF)

Multi-channel operational amplifiers (op amps) are often implemented in circuits that do not require the use of all channels. Undesired behavior in an unused amplifier channel can negatively impact system performance, as well as the performance of the channels in use. To avoid degradation of both the op amp and system performance, the unused op amp channels must be configured properly.

from Dangerous Prototypes https://ift.tt/2GTQ7gU

App note: Current sense amplifiers in class-D audio subsystems

an_ti_slva031

App note from Texas Instruments about output current sensing in class-D amplfiers. Link here (PDF)

Current sensing in audio subsystems are widely used in conjunction with CLASS-D amplifiers for diagnostics or to provide speaker current feedback to the DSP for speaker enhancement to emulate smartamp. The most expensive component in the audio subsystem is the speaker. The impedance of the speakers ranges from 2Ω for subwoofer to a 8Ω for stereo speakers. Exceeding the current flowing through the speakers has a potential to create excessive heat in the voice coil which can lead to permanent damage of the speakers.

from Dangerous Prototypes https://ift.tt/2xnLOuS