#FreePCB via Twitter to 2 random RTs

BP

Every Tuesday we give away two coupons for the free PCB drawer via Twitter. This post was announced on Twitter, and in 24 hours we’ll send coupon codes to two random retweeters. Don’t forget there’s free PCBs three times a every week:

  • Hate Twitter and Facebook? Free PCB Sunday is the classic PCB giveaway. Catch it every Sunday, right here on the blog
  • Tweet-a-PCB Tuesday. Follow us and get boards in 144 characters or less
  • Facebook PCB Friday. Free PCBs will be your friend for the weekend

Some stuff:

  • Yes, we’ll mail it anywhere in the world!
  • Check out how we mail PCBs worldwide video.
  • We’ll contact you via Twitter with a coupon code for the PCB drawer.
  • Limit one PCB per address per month please.
  • Like everything else on this site, PCBs are offered without warranty.

We try to stagger free PCB posts so every time zone has a chance to participate, but the best way to see it first is to subscribe to the RSS feed, follow us on Twitter, or like us on Facebook.

from Dangerous Prototypes https://ift.tt/2B4yg77

Simple homebrew 6502 computer

homebrew6502_003

Sven Krasser blogged about his 6502-based homebrew 8-bit computer build:

After completing my VGA Generator project a while back, I’ve embarked on a new electronics project: building a simple 6502-based homebrew 8-bit computer on a breadboard. There are a bunch of similar projects online from which to draw ideas. Some projects set constraints such as only using contemporary parts of the 8-bit era, no FPGAs, no microcontrollers etc. In my case, I opted instead to keep the constraints minimal and the project simple.

See the full post on his blog here.

Check out the video after the break.

from Dangerous Prototypes https://ift.tt/2qHHrEA

Making an e-Paper Etch-a-Sketch

epaper-etch-a-sketch

Scott Baker has been working on making an Etch-a-Sketch using modern e-Paper displays and optical encoders:

Above you can see my prototype. I’m using a 4.2″ e-Paper display from Gooddisplay, together with the Waveshare breakout board. I have a couple of ENS1J-B28-R00128 optical encoders that I attained on eBay. I specifically chose these encoders instead of traditional electro-mechnical encoders due to the high numbers of pulses per revolution. A typical electro-mechanical encoder will net about 24 pulses per revolution. The optical encoders I bought on ebay are 128 pulses per revolution. Our 4.2″ ePaper has 400×300 pixels. To traverse the major axis would require 16 full turns of the electromechical encoder but only 3 turns of the optical encoder.
The hardware is so simple that there’s not much more to say. The encoders are connected to GPIO pins of a Raspberry Pi. Note that there are resistors inline on the encoder outputs as the encoders are 5V and the Raspberry Pi uses 3.3V GPIO. The e-ink display is connected to the SPI bus.

See the full post on his blog here and the GitHub repository here.

Check out the video after the break.

from Dangerous Prototypes https://ift.tt/2Di5rpa

Free PCB Sunday: Pick your PCB

BP-600x373

We go through a lot of prototype PCBs, and end up with lots of extras that we’ll never use. Every Sunday we give away a few PCBs from one of our past or future projects, or a related prototype. Our PCBs are made through Seeed Studio’s Fusion board service. This week two random commenters will get a coupon code for the free PCB drawer tomorrow morning. Pick your own PCB. You get unlimited free PCBs now – finish one and we’ll send you another! Don’t forget there’s free PCBs three times every week:

Some stuff:

  • Yes, we’ll mail it anywhere in the world!
  • Be sure to use a real e-mail in the address field so we can contact you with the coupon.
  • Limit one PCB per address per month please.
  • Like everything else on this site, PCBs are offered without warranty.
  • PCBs are scrap and have no value, due to limited supply it is not possible to replace a board lost in the post

Be the first to comment, subscribe to the RSS feed.

from Dangerous Prototypes https://ift.tt/2zI7zTW

App note: Blood pressure monitor fundamentals and design

an_nxp_an4328

Application note from NXP on blood pressure monitor fundamentals using their medical oriented MCUs. Link here (PDF)

Arterial pressure is defined as the hydrostatic pressure exerted by the blood over the arteries as a result of the heart left ventricle contraction. Systolic arterial pressure is the higher blood pressure reached by the arteries during systole (ventricular contraction), and diastolic arterial pressure is the lowest blood pressure reached during diastole (ventricular relaxation). In a healthy young adult at rest, systolic arterial pressure is around 110 mmHg and diastolic arterial pressure is around 70 mmHg.

from Dangerous Prototypes https://ift.tt/2Dz8wlN

App note: How to eliminate over stress of MOSFET during start-up of flyback converter

an_richtek_an010

App note from Richtek about their embedded soft-start function to eliminate MOSFET stress. Link here

Switching Power Supply, compared to Linear Power Supply, is widely used due to its advantages, such as small size, light weight, high efficiency, etc. Flyback Converter, one of the switching power supply topologies, is most suitable for power supply systems that are below 150W because of its unique features of isolation between primary and secondary sides, simple circuit architecture, few components, low cost, etc.

Since switching power MOSFETs play a very important role in switching power supply converters, how to effectively eliminate over-stress of MOSFET during the start-up of flyback converters will be the main focus to be discussed in this application note. The three major aspects to be investigated are flyback controller design, feedback stability, and Snubber design.

from Dangerous Prototypes https://ift.tt/2JTfYIH

Grbl_ESP32 development board version 3.1

20181007_153826

A board to control your CNC machine with Grbl_ESP32 designed by Bart Dring, that is available on GitHub:

This is a Grbl_ESP32 CNC Development board. This is a quick and easy way to use and test CNC on the ESP32 controller.
Grbl is a great CNC firmware that has been around for nearly a decade. It was originally designed for the Arduino UNO and basic 3 axis CNC routers, but it has been ported to other CPUs and was the basis for many other CNC and 3D printer firmwares.
The firmware was written using the Arduino IDE to make it as user friendly as possible. If you have experience with Arduinos, this will not be much different.

Project info at Buildlog.Net Blog. It’s also up on Tindie.

from Dangerous Prototypes https://ift.tt/2DdabN2

Free PCB coupon via Facebook to 2 random commenters

BP

Every Friday we give away some extra PCBs via Facebook. This post was announced on Facebook, and on Monday we’ll send coupon codes to two random commenters. The coupon code usually go to Facebook ‘Other’ Messages Folder . More PCBs via Twitter on Tuesday and the blog every Sunday. Don’t forget there’s free PCBs three times every week:

Some stuff:

  • Yes, we’ll mail it anywhere in the world!
  • We’ll contact you via Facebook with a coupon code for the PCB drawer.
  • Limit one PCB per address per month, please.
  • Like everything else on this site, PCBs are offered without warranty.

We try to stagger free PCB posts so every time zone has a chance to participate, but the best way to see it first is to subscribe to the RSS feed, follow us on Twitter, or like us on Facebook.

from Dangerous Prototypes https://ift.tt/2Da8hg5

A simple 8-channel receiver voting controller for enhanced repeater coverage and usability

R0300146

KA7OEI has written an article detailing a simple 8-channel receiver voting controller:

To simplify things, this voting controller sits in “front” of an ordinary repeater controller, taking the audio and COS inputs from the various receivers and outputting a single audio and COS signal.
If the repeater system in question uses subaudible tones, it is recommended that “discriminator” audio (e.g. that which has not been de-emphasized) that has not been subject to a squelch or tone detector audio gate be applied to the voting controller from the link receivers as well as any “local” receivers as this will assure that the voted audio will contain the subaudible tone.

More details on KA7OEI ‘s blog.

from Dangerous Prototypes https://ift.tt/2PMs4Jb